manualshive.com logo in svg

CoolBot Walk-in Cooler, Руководство по монтажу

Поделиться
Скачать
CoolBot Walk-in Cooler Скачать руководство пользователя страница 17

 

 

 

 

PHONE: 888-871-5723 

 

 

[email protected] 

 

2018 © Store It Cold, LLC. 

Rev 2018-9a 

All Rights Reserved.  

 

WALK-IN COOLER INSTALLATION WITH OUT FLOOR OPTION 

YOUR WALK-IN COOLER PANELS, DOOR, SCREEDING OR OUTDOOR PACKAGE PARTS MIGHT 

DIFFER IN DESIGN OR LOOKS FROM THE ONES SHOWN IN THIS MANUAL.

 

1.

 

Use a chalk line to mark the installation area to the dimensions of the walk-in as shown 
in the drawing (Figure 1). Measure diagonally from corner to corner to be sure the floor 
vinyl screed is square.  
 

2.

 

Apply TWO straight beads of silicone along the bottom of the vinyl screed (about an inch 
away from the edges), then place the vinyl screed along the chalk lines.  

NOTE

: Leave the vinyl screed loose until the walk in is assembled. DO NOT anchor to the 

floor. 

NOTE

: The vinyl screed might have to be cut as all pieces are not cut to measure from the 

factory. Use a miter saw or a hand saw to cut the screeding. 

 

3.

 

Begin with two corner panels. Usually the left back corner is a good place to start. Stand 
the wall panels inside the screed making sure they sit correctly (fully cradled in the 
screeding). Make sure that the top of each wall adjacent panel is flush with each other. 
Use the wrench to secure the wall panels together to start the wall. Check for alignment 
to make sure the panels are flush with each other as you proceed. 

 

 

4.

 

Select the next adjacent wall panel, going in a clockwise direction around the perimeter 
and follow the same steps as above: Align, lock to the adjacent wall panel and double 

Содержание Walk-in Cooler































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды