Control Techniques Unidrive 1 Series Скачать руководство пользователя страница 53

Страница: 53 / 208

Safety

Information

Product

Information

Mechanical

Installation

Electrical

Installation

Getting
Started

Menu 0

Running

the motor

Optimisation

Macros

Advanced

Parameters

Technical

Data

Diagnostics

UL Listing

Information

Unidrive User Guide

Issue Number: 9 www.controltechniques.com

The default configuration of the above digital inputs and outputs are
different for Unidrive VTC. See Figure 4-16

Unidrive VTC default

terminal functions (European and USA)

on page 51 and section

4.9.3

Unidrive VTC control terminal default configuration

on page 54 for

details.

Analog output 1

OL> FREQUENCY output signal
CL> SPEED output signal

Analog output 2

TORQUE output signal

Type of output

Bipolar single-ended analog voltage or
unipolar current output

Mode controlled by...

7.19

7.22

Operating in Voltage mode

Output voltage range

10V

Maximum output current

10mA peak

Load resistance

Ω

minimum

Protection

Short-circuit proof

Operating in current mode

Current ranges

0 to 20mA
4 to 20mA

Maximum output voltage

12V

Maximum load resistance

600

Ω

Equivalent input resistance

≤

200

Ω

at 20mA

Common to all modes

Resolution

10-bit plus sign

Update period

PWM switching frequency dependent
5.5ms for 3, 6, & 12kHz
7.4ms for 4.5 & 9kHz

0V common (analog)

Function

Common connection for external
analog devices.

0V common (digital)

+24V digital supply

Function

Supply for external digital signal
devices

Voltage tolerance

10%

Nominal output current

200mA (total including any digital
outputs)

Overload output current

240mA (total including any digital
outputs)

Protection

Current foldback above 240mA

0V common (digital)

Function

Common connection for external digital
devices.

Digital input / output F1

OL> AT-SPEED output
CL> AT ZERO SPEED output

Digital input / output F2 RESET input

Digital input / output F3 JOG SELECT input

Type of output

Negative or positive logic digital inputs,

negative-logic push-pull or open

collector digital outputs

Input / output mode controlled by...

Parameters

8.12

8.15

8.18

Operating as an input

Logic mode controlled by...

Parameter

8.27

Absolute maximum voltage range

-3V to +30V

Input current when 0V applied

≥

3.2mA

Negative-logic levels

Inactive state (input open-circuit):
>+15V
Active state: <+5V

Positive-logic levels

Inactive state (input open-circuit): >+5V
Active state: <+15V

Operating as an output

Open collector outputs selected by...

Parameter

8.28

Maximum output current

200mA (total including terminal 22)

Overload output current

240mA (total including terminal 22)

Common to both modes

Voltage range

0V to +24V

Sample / Update period

PWM switching frequency dependent
5.5ms for 3, 6, & 12kHz
7.4ms for 4.5 & 9kHz

Digital input F4

RUN FORWARD input

Digital input F5

RUN REVERSE input

Digital input F6

ANALOG INPUT 1 / INPUT 2
SELECT INPUT

Type

Negative or positive logic digital inputs

Logic mode controlled by...

Parameter

8.27

Voltage range

0V to +24V

Absolute maximum
voltage range

–3V to +30V

Input current when 0V applied

≥

3.2mA

Negative-logic levels

Inactive state (input open-circuit):
>+15V
Active state: <+5V

Positive-logic levels

Inactive state (input open-circuit): <+5V
Active state: >+15V

Sample period

PWM switching frequency dependent
5.5ms for 3, 6, & 12kHz
7.4ms for 4.5 & 9kHz

Содержание Unidrive 1 Series

















































































































































































































Результаты поиска

Содержание Unidrive 1 Series

Отзывы:

Бренды по названию

Популярные бренды

Control Techniques Unidrive 1 Series, Руководство пользователя

Результаты поиска

Содержание Unidrive 1 Series

Отзывы:

Бренды по названию

Популярные бренды