manualshive.com logo in svg

Control Techniques UD77 DeviceNet, Руководство пользователя

Поделиться
Скачать
Control Techniques UD77 DeviceNet Скачать руководство пользователя страница 46

 

46 Issue 

Number: 

 

 

2 

9.11.6 Ready 

Class:  41 (0x29) 

Instance:  1 (0x1) 

Attribute:  9 (0x9) 

Read only attribute that indicates that the drive is enabled and ready to 
run. 

Action Mapping 

Read #6.15 

9.11.7 Faulted 

Class:  41 (0x29) 

Instance:  1 (0x1) 

Attribute:  10 (0xA) 

Read only attribute that indicates that the drive tripped when set to 1.   

Action Mapping 

Read !#10.01 

NOTE 

This is the opposite polarity to #10.01 on the Unidrive. 

9.11.8 FaultRst 

Class:  41 (0x29) 

Instance:  1 (0x1) 

Attribute:  12 (0xC) 

Set to 1 to reset a drive from a tripped condition.  Note that with 
Unidrive, this will cause a complete reset of the DeviceNet interface.  

Action Mapping 

Write (0) 

No action 

Write (1) 

#10.38 = 100 

9.11.9 FaultCode 

 

Class:  41 (0x29) 

Instance:  1 (0x1) 

Attribute:  13 (0xD) 

Returns a fault code number, indicating the reason why the drive 
tripped.  Refer to the Unidrive or Mentor II User’s Guides for a full list of 
fault codes. 

Action Mapping 

Read #10.20 

Under normal operating conditions, the Unidrive and Mentor II will be in 
the “Drive Healthy” condition, indicating that the drives are operating 
with no problems.  This condition is indicated by a value of 1 in #10.01 
on Unidrive. 

If a drive trips for any reason, the drive healthy bit is reset to 0, and a 
diagnostic code is provided to indicate the reason for the trip.  This code 
is available from #10.20 in the Unidrive. 

Содержание UD77 DeviceNet

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды