Control Techniques UD77 DeviceNet Скачать руководство пользователя страница 25

 

Issue Number:   2 

25 

7 Support 

Files 

7.1 What 

are 

EDS 

Files? 

EDS (Electronic Data Sheets) files are text files that are used by 
DeviceNet network configuration software tools.  They contain 
information about the device, such as manufacturer, product type, 
product code, etc, and they also provide information on the default 
settings and functions supported by the device.  Mapping information is 
also included that allows access to device parameters over the 
DeviceNet network. 

EDS files are not downloaded to the PLC or scanner, and are only used 
during network configuration.  It is actually possible to configure a 
network without the EDS files, but they do help to provide a good 
picture of the network within the network configuration software. 

7.2 Generic 

EDS 

Files 

Generic EDS files are available that support Unidrive fitted with Version 
2 and Version 3 software, and configured in open loop, closed loop and 
servo mode.  Generic EDS files for Mentor II and Commander SE are 
also supplied.  These files are available from your local Control 
Techniques Drive Centre. 

These files contain a basic common selection of the drive parameters, 
allowing configuration of speed or torque references, acceleration and 
deceleration ramps, motor data set-up, digital and analogue I/O 
configuration parameters, and DeviceNet configuration parameters. 

Unidrive Open Loop 

G3_OPEN.EDS 

G2_OPEN.EDS 

Unidrive Closed Loop  G3_CLSD.EDS 

G2_CLSD.EDS 

Unidrive Servo 

G3_SERVO.EDS 

G2_SERVO.EDS 

Mentor II 

G410_M4Q.EDS 

G501_M4Q.EDS 

Mentor II 

G502_M4Q.EDS 

G504_M4Q.EDS 

Mentor II 

G505_M4Q.EDS 

 

Commander SE 

G1_CSE.EDS 

 

Drive icon files are also supplied for use with the DeviceNet 
configuration software being used.  EDS files must usually be installed 
into the software package being used to configure a DeviceNet network.  
Refer to the software documentation for instructions on how to install 
EDS files.  Control Techniques cannot provide specific technical 
support for any of these software packages. 

Содержание UD77 DeviceNet

























































Отзывы: