manualshive.com logo in svg

Control Techniques UD77 DeviceNet, Руководство пользователя

Поделиться
Скачать
Control Techniques UD77 DeviceNet Скачать руководство пользователя страница 36

 

36 Issue 

Number: 

 

 

2 

There are 3 ways to select a pre-defined Input or Output assembly 
object: 

1.  Use the PLC Explicit communications to write directly to the 

Control Supervisor.  (See page 43 in DeviceNet User Guide Issue 
1.)  The relevant attributes are 100 (Output) and 101 (Input).  

2.  Use the Class Instance Editor within RSNetworx to modify the 

Control Supervisor directly yourself.  Refer to page 43 to check the 
supported services for Unidrive DeviceNet interface. 

3. 

Double-click on a node to go on-line to it, and look under the group 

"DeviceNet Config".  In this group, you will find the attributes 
"Polled Input Assembly" and "Polled Output Assembly".  Update 
with the appropriate value. 

NOTE 

The parameter mapping of the pre-defined DeviceNet objects CANNOT 
be changed. 

9.7.1 Basic 

Speed 

Control 

Output Assembly Object 20 

The scanner must be configured for 4 Tx bytes (or 2 Tx words) if this 
output assembly object is selected. 

Word Function 

Word 0 

Basic Control Word (See section  9.11) 

Word 1 

Speed Reference (See section 9.11.13) 

The Basic Control Word uses a full 16-bit word, with the bits having 
functions as shown below.  Refer to section 9.11 for mapping details of 
each function. 

b15 b14 b13 B12 b11  B10  b9 

b8 

 

 

 

 

 

 

 

 

 

b7 b6 b5 b4 b3  B2  b1  b0 

 

 

 

 

 FaultRst  RunFwd 

 

Содержание UD77 DeviceNet

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды