manualshive.com logo in svg

Control Techniques UD77 DeviceNet, Руководство пользователя

Поделиться
Скачать
Control Techniques UD77 DeviceNet Скачать руководство пользователя страница 26

 

26 Issue 

Number: 

 

 

2 

7.3 EDS 

File 

Revisions 

The EDS files from Control Techniques have undergone several 
revisions as specifications have been changed or tightened up.  The 
table below shows the compatibility with the most common DeviceNet 
configuration tools. 

EDS 

Revision 

DeviceNet 

Manager 

RSNetworx 

1.x OK Not 

compatible 

2.x 

OK 

V2.xx.xx and earlier 

3.x OK 

V3.xx.xx 

7.4 Advanced 

EDS 

Files 

Advanced EDS files provide access to the complete drive parameter set 
for a specific version of software.  This al so includes parameters for any 
small option module that may be fitted to the drive.  Advanced EDS files 
must be created using the Advanced EDS File Compiler, available from 
your local Control Techniques Drive Centre. 

To use an advanced EDS file: 

1. 

Specify the Unidrive mode to be used. 

2. 

Specify the type of small option module fitted 

3. 

Specify the nearest matching software version 

4. 

Make a note of the “Product Code Elaboration” value specified for 

#20.12. 

5. Build 

the 

EDS 

file. 

6. 

Install the EDS file into the DeviceNet configuration software. 

7. 

Set #20.12 as specified for the Unidrive 

8. 

Set #17.19 to 1 to store and reset the UD70.  (See section 4.9) 

When the network is re-scanned, the product code of the Unidrive will 
have changed, and this should be matched to the EDS file that has just 
been created. 

 

Содержание UD77 DeviceNet

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды