Control Techniques SM-Encoder Output Plus Скачать руководство пользователя страница 38

Страница: 38 / 42

SM-Encoder Plus & SM-Encoder Output Plus User Guide

www.controltechniques.com

Issue: 4

Terminal data

8.1

Encoder inputs (PL1)

Ab, Fd, and Fr encoders

8.1.1

SM-Encoder Plus

8.1.2

SM-Encoder Output Plus

The encoder supply voltage is controlled by Pr

x.13

. The default for this parameter is 5V

(0) but this can be set to 8V (1) or 15V (2). Setting the encoder voltage supply too high
for the encoder could result in damage to the feedback device.
The termination resistors should be disabled (Pr

x.16

= 0) if the outputs from the

encoder are higher than 5V.

Channel A, Frequency or Forward inputs

Channel A\, Frequency\ or Forward\ inputs

Channel B, Direction or Reverse inputs

Channel B\, Direction\ or Reverse\ inputs

Marker pulse channel Z

Marker pulse channel Z\

Type

EIA 485 differential receivers

Maximum frequency

500kHz

Line loading

<2 unit loads

Line termination components

120

Ω

Working common mode range

+12Vdc to –7Vdc

Absolute maximum applied voltage relative to
0V

25V

Absolute maximum applied differential voltage

25V

0V Common

External power supply decoupling

Maximum voltage

50Vdc

Encoder supply voltage

Supply voltage

5V, 8V or 15V

Maximum output current

300mA for 5V and 8V
200mA for 15V

Содержание SM-Encoder Output Plus











































Результаты поиска

Содержание SM-Encoder Output Plus

Отзывы:

Похожие инструкции для SM-Encoder Output Plus

Бренды по названию

Популярные бренды

Control Techniques SM-Encoder Output Plus, Руководство пользователя

Результаты поиска

Содержание SM-Encoder Output Plus

Отзывы:

Похожие инструкции для SM-Encoder Output Plus

Бренды по названию

Популярные бренды