Control Techniques SM-Encoder Output Plus Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 42

background image

36

SM-Encoder Plus & SM-Encoder Output Plus User Guide

www.controltechniques.com

Issue: 4

Any trip can be initiated by writing the relevant trip number to Pr

10.38

. If any trips

shown as user trips are initiated the trip string is "txxx", where xxx is the trip number.
Trips can be reset after 1.0s if the cause of the trip has been rectified.
A full list of drive trips can be found in the appropriate drive manual.

Table 7.1 Trip codes

Trip

Diagnosis

C.Optn

SMARTCARD trip: Solutions Modules fitted are different between source drive
and destination drive

180

Ensure correct Solutions Modules are fitted
Ensure Solutions Modules are in the same Solutions Module slot
Press the red

reset button

Enc1

Drive encoder trip: Encoder power supply overload

189

Check encoder power supply wiring and encoder current requirement
Maximum current = 200mA @ 15V or 300mA @ 8V and 5V

Enc2

Drive encoder trip: Wire break (Drive encoder terminals 1 & 2, 3 & 4, 5 & 6)

190

Check cable continuityCheck wiring of feedback signals is correct
Check encoder power supply is set correctly
Replace feedback device
If wire break detection on the main drive encoder input is not required, set Pr

3.40

= 0

to disable the Enc2 trip

PS.24V

24V internal power supply overload

9

The total user load of the drive and Solutions Modules has exceeded the internal 24V
power supply limit.
The user load consists of the drive’s digital outputs plus the SM-I/O Plus digital
outputs, or the drive’s main encoder supply plus the SM-Universal Encoder Plus and
SM-Encoder Output Plus encoder supplies.
•

Reduce load and reset

•

Provide an external 24V >50W power supply

•

Remove any Solutions Modules and reset

SLX.dF

Solutions Module slot X trip: Solutions Module type fitted in slot X changed

204,209,

214

Save parameters and reset

SLX.Er

Solutions Module slot X trip: Error detected with Solutions Module, where X is
the slot number

202
207
212

When the drive is reset this parameter is cleared for the relevant Solutions Module

SLX.HF

Solutions Module slot X trip: Solutions Module X hardware fault

200,205,

210

Ensure Solutions Module is fitted correctly
Return Solutions Module to supplier

Pr x.50 Fault description

0

No errors

1

Power supply overloaded

«
...
34
35
36
37
38
...
»

Содержание SM-Encoder Output Plus











































Отзывы:

Нет отзывов

Похожие инструкции для SM-Encoder Output Plus

Бренд: Baldor Страницы: 55

COMFOSPLIT IKARO

Бренд: Ideal Clima Страницы: 68

Бренд: Digitrax Страницы: 8

Бренд: Briggs & Stratton Страницы: 60

Бренд: Teracue Страницы: 68

Бренд: Costway Страницы: 25

HDMI Super Booster Plus

Бренд: Gefen Страницы: 10

Бренд: DAISHIN Страницы: 28

Бренд: argon audio Страницы: 6

Бренд: Plexim Страницы: 8

Бренд: Wisenet Страницы: 8

Бренд: C2G Страницы: 263

Бренд: Prism Sound Страницы: 63

Бренд: G2 Страницы: 13

Бренд: Barco Страницы: 4

Бренд: MRC Страницы: 2

Бренд: SOtM Страницы: 20

NX Distributed Intelligence NX MEDIA CONVERTER

Бренд: Hubbell Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды