Comtech EF Data CDM-Qx, Инструкция по установке и эксплуатации

Страница: 186 / 224

CDM-Qx Satellite Modem Revision 6
Remote Control MN/CDMQx.IOM
Parameter
Type
Command
(Instruction
Code and
qualifier)
Arguments
for Command
or Response
to Query
Description of Arguments
Response to
Command
(Target to
Controller)
Query
(Instruction
Code and
Qualifier)
Response to
query
(Target to
Controller)
Circuit ID String CID= 28 bytes Command or Query
Sets or queries the user-defined Circuit ID string which is a fixed
length of 28 characters.
Valid characters include:
Space( ) * + - , ./0 9,and A through Z CID=
CID?
CID*
CID#
CID^ CID? CID=-
xxxxxxxxxxxxxxxxxx
xxxxxxxxxx
(see description of
arguments)
Quad Drop & Insert
(applies to
cards
grouped as
modem) QDI= 77 bytes Quad Drop & Insert Commands (E1 CCS Only) Command or query.
QDI=pccdddddddddddddddddddddddddddddddtCCiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiTLMrrrrrr
p = Port number 1 thru 4
cc = Number of Drop Channels, 0-32. Used to decide Port p’s TX Tributary Rate
if Interface Type is Quad Drop & Insert (ITF=D).
31 bytes of Drop information:
d = 31 bytes defining Timeslot locations (or channels)
t = Drop type: (0=reserved, 1=reserved, 2=E1-CCS, 3=reserved)
CC = Number of Insert Channels, 0-32. Used to decide Port p’s RX Tributary
Rate if Interface Type is Quad Drop & Insert (ITF=D).
31 bytes of Insert information:
I = 31 bytes defining Timeslot locations (or channels)
T = Insert type: (0=reserved, 1=reserved, 2=E1-CCS, 3=reserved)
Timeslot definition:
0 = Unused
1-9 for timeslots 1–9, A=10, B=11, C=12, D=13…V=31.
L = Line Code: (0=AMI, 1=reserved, 2=HDB3)
M = reserved (set to value 0)
r = reserved (set to value 0)
Example 1:
131123456789ABCDEFGHIJKLMNOPQRSTUV231123456789ABCDEFGHIJK
LMNOPQRSTUV200000000
Port 1’s Drop channels 1–31 using timeslots 1–31. Same for Insert. Port 1’s Line
code is AMI.
Example 2:
304123400000000000000000000000000020412340000000000000000000000
00000220000000
Port 3’s Drop channels 1–4 using timeslots 1–4. Same for Insert. Port 3’s Line
code is HDB3-_.
Notes:
1.
This command is a bit forgiving in the sense that the modem accepts the
command even though the interface type is other than Quad Drop &
Insert. This was intentional because it’s being used with the CRS-300
switch for 1:N redundancy.
2. To select Full E1 for the port, set Number of Drop/Insert channel to
be 32, and the timeslot locations to be
“123456789ABCDEFGHIJKLMNOPQRSTU”.
QDI=
QDI?
QDI*
QDI#
QDI$
QDI^
QDI?p
QDI?pn
QDI=pccddddddddd
dddddddddddddddd
ddddddtCCiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiTLMrrrrrr
(see description of
arguments)
Returns current
Drop and Insert
configuration of a
single port.
Where n=0 to 9
returns the QDI
portion of 1 of 10
stored
configurations for a
single port on Quad
Drop & Insert
Interface.
C-20