manualshive.com logo in svg

Compaq AlphaServer ES40, Руководство пользователя

Поделиться
Скачать
Compaq AlphaServer ES40 Скачать руководство пользователя страница 67

Booting and Installing an Operating System   

3-1

Chapter 3

Booting and Installing

an Operating System

This chapter gives instructions for booting the Tru64 UNIX, OpenVMS, or
Linux operating systems and for starting an operating system installation.  It
also describes how to switch from one operating system to another.  Refer to
your operating system documentation for complete instructions on booting or
starting an installation.

The following topics are covered:

•

 

Setting Boot Options

•

 

Booting Tru64 UNIX

•

 

Starting a Tru64 UNIX Installation

•

 

Booting OpenVMS

•

 

Starting an OpenVMS Installation

•

 

Booting Linux

•

 

OpenVMS Galaxy

•

 

Switching Between Operating Systems

NOTE: Your system may have been delivered to you with factory-installed

software (FIS); that is, with a version of the operating system already
installed.  If so, refer to the FIS documentation included with your
system to boot your operating system for the first time.  Linux-ready
systems do not come with factory-installed software.

Содержание AlphaServer ES40





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды