Compaq AlphaServer ES40 Скачать руководство пользователя страница 208

Страница: 208 / 228

7-28

ES40 Owner’s Guide

Table 7–8 Boot Problems

Symptom

Action

System cannot find
boot device.

Check the system configuration for the correct device
parameters (node ID, device name, and so on).

Use the show config and show device commands.

Check the system configuration for the correct
environment variable settings.

Examine the auto_action, bootdef_dev,
boot_osflags, and os_type environment variables.

For network boots, make sure ei*0_protocols or
ew*0_protocols is set to bootp for UNIX or mop
for OpenVMS.

Device does not boot.

For problems booting over a network, make sure
ei*0_protocols or ew*0_protocols is set to bootp
for UNIX or mop for OpenVMS.

Run the test command to check that the boot device
is operating.

Содержание AlphaServer ES40





































































































































































































































Результаты поиска

Содержание AlphaServer ES40

Отзывы:

Бренды по названию

Популярные бренды

Compaq AlphaServer ES40, Руководство пользователя

Результаты поиска

Содержание AlphaServer ES40

Отзывы:

Бренды по названию

Популярные бренды