manualshive.com logo in svg

Compaq AlphaServer ES40, Руководство пользователя

Поделиться
Скачать
Compaq AlphaServer ES40 Скачать руководство пользователя страница 53

Operation    

2-19

➎

PCI bus information.

The “Slot” column lists the logical slots seen by the system.  They are not
the physical slots into which devices are installed.  See Table 2–1 for the
correspondence between logical slots and physical slots.

The NCR 53C896 on Hose 0, Bus 0 is a dual-channel Ultra2 SCSI
multifunction controller.  Two controllers reside on the same chip.  They
are shown as 2/0 and 2/1.  The first number is the logical slot, and the
second is the function.

The Acer Labs bridge chip, which is located in PCI logical slot 7, has two
built-in IDE controllers.  The CD-ROM is on the first controller.

NOTE: The naming of devices (for example,dqa.0.0.15.0) follows the

conventions described in Table 2–2.

In Example 2–5, the following devices are present:

Hose 0, Bus 0, PCI
Slot 2/0

SCSI controller

Slot 2/1

SCSI controller

Slot 4 

VGA controller

Slot 7

PCI to ISA bridge chip

Slot 15

IDE controller and CD-ROM drive

Slot 19

Universal serial bus (USB) controller

Hose 0, Bus 1, ISA
Diskette drive

Hose 1, Bus 0, PCI
Slot 1

SCSI controller and drives

Slot 3

SCSI controller and drives

Slot 4

Ethernet controller

Slot 6

PCI-to-PCI bridge chip to Bus 2

Hose 1, Bus 2, PCI
Slot 0

SCSI controller

Slot 1

SCSI controller

Slot 2

Ethernet controller

Содержание AlphaServer ES40





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды