manualshive.com logo in svg

Compaq AlphaServer ES40, Руководство пользователя

Поделиться
Скачать
Compaq AlphaServer ES40 Скачать руководство пользователя страница 194

7-14

    ES40 Owner’s Guide

7.4.3

 

Test Command

The test command verifies all the devices in the system.

Example 7–4   Test Command

P00>>> test
Testing the Memory
Testing the DK* Disks(read only)
No DU* Disks available for testing
No DR* Disks available for testing
Testing the DQ* Disks(read only)
Testing the DF* Disks(read only)
No MK* Tapes available for testing
No MU* Tapes available for testing
Testing the DV* Floppy Disks(read only)
Testing the VGA (Alphanumeric Mode only)
Testing the EWA0 Network
Testing the EWB0 Network
P00>>>

The test command also does a quick test on the system speaker.  A beep is
emitted as the command starts to run.

The tests are run sequentially, and the status of each subsystem test is
displayed to the console terminal as the tests progress.  If a particular device is
not available to test, a message is displayed.  The test script does no destructive
testing; that is, it does not write to disk drives.

The syntax is:

test  [argument]

Use the -lb (loopback) argument for console loopback tests.

To run a complete diagnostic test using the test command, the system
configuration must include:

•

 

A serial loopback connected to the COM2 port (not included)

•

 

A parallel loopback connected to the parallel port (not included)

Содержание AlphaServer ES40





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды