manualshive.com logo in svg

Comnet CNGE20MS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CNGE20MS Скачать руководство пользователя страница 95

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 95

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

RADIUS Overview

This page provides an overview of the status of the RADIUS servers configurable on the 
Authentication configuration page.

RADIUS Authentication Servers

Label

Description

#

The RADIUS server number. Click to navigate to detailed statistics for this server.

IP Address

The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this 
server.

Status

The current status of the server. This field takes one of the following values: 
Disabled: The server is disabled. 
Not Ready: The server is enabled, but IP communication is not yet up and running. 
Ready: The server is enabled, IP communication is up and running, and the RADIUS 
module is ready to accept access attempts. 
Dead (X seconds left): Access attempts were made to this server, but it did not reply 
within the configured timeout. The server has temporarily been disabled, but will get 
re-enabled when the dead-time expires. The number of seconds left before this occurs 
is displayed in parentheses. This state is only reachable when more than one server is 
enabled.

Содержание CNGE20MS

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды