Comnet CNGE20MS Скачать руководство пользователя

Страница: 72 / 144

INS_CNGE24MS-OB(M,S)_REV–

09/12/12 PAGE 72

INSTALLATION AND OPERATION MANUAL

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Port Shaping

This page provides an overview of QoS Egress Port Shapers for all switch ports.

Label

Description

Port

The logical port for the settings contained in the same row.
Click on the port number in order to configure the shapers.

Mode

Shows “disabled” or actual queue shaper rate – e.g. “800 Mbps”.

Shows “disabled” or actual port shaper rate – e.g. “800 Mbps”.

DSCP Based QoS

This page allows you to configure the basic QoS DSCP based QoS Ingress Classification settings
for all switches.

Label

Description

DSCP

Maximum number of supported DSCP values are 64.

Trust

Controls whether a specific DSCP value is trusted. Only frames with trusted DSCP values
are mapped to a specific QoS class and Drop Precedence Level. Frames with untrusted
DSCP values are treated as a non-IP frame.

QoS Class

QoS class value can be any of (0-7)

DPL

Drop Precedence Level (0-1)

Содержание CNGE20MS

















































































































































Результаты поиска

Содержание CNGE20MS

Отзывы:

Похожие инструкции для CNGE20MS

Бренды по названию

Популярные бренды

Comnet CNGE20MS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CNGE20MS

Отзывы:

Похожие инструкции для CNGE20MS

Бренды по названию

Популярные бренды