manualshive.com logo in svg

Comnet CNGE20MS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CNGE20MS Скачать руководство пользователя страница 12

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 12

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Pin Number

Assignment

1

BI_DA+

2

BI_DA-

3

BI_DB+

4

BI_DC+

5

BI_DC-

6

BI_DB-

7

BI_DD+

8

BI_DD-

 

1000 BASE-T RJ-45 Pin Assignments

The CNGE24MS-OB(M,S) switch supports auto MDI/MDI-X operation. You can use a straight-
through cable to connect a PC to the switch. The table below shows the 10/100BASE-T(X) MDI and 
MDI-X port pin outs.

Pin Number

MDI port 

MDI-X port

1

TD+(transmit)

RD+(receive)

2

TD-(transmit)

RD-(receive)

3

RD+(receive)

TD+(transmit)

4

Not used

Not used

5

Not used

Not used

6

RD-(receive)

TD-(transmit)

7

Not used

Not used

8

Not used

Not used 

10/100 BASE-T MDI/MDI-X pins assignment

Pin Number

MDI port 

MDI-X port

1

BI_DA+

BI_DB+

2

BI_DA-

BI_DB-

3

BI_DB+

BI_DA+

4

BI_DC+

BI_DD+

5

BI_DC-

BI_DD-

6

BI_DB-

BI_DA-

7

BI_DD+

BI_DC+

8

BI_DD-

BI_DC-

1000 BASE-T MDI/MDI-X pins assignment

Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.

Содержание CNGE20MS

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды