ComAp InteliGen NT Скачать руководство пользователя

Страница: 35 / 44

InteliGen

, InteliSys

, InteliMains

– Troubleshooting Guide,

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp

– August 2018

IGS-NT Troubleshooting Guide.pdf

IGS-NT Alarm/History

record

Alarm/

History

Appeara

nce

Description

phase to neutral voltages. It means that

Basic settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BusL L1, L2 or L3 over

Left bus L1, L2 or L3 voltage was over the

BusLeft >V

limit

for the

BusLeft V del

time

Information about that is

recorded into controller history.
Setpoint

BusL protect

BusL Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be below the

BusLeft

limit if BTB synchronisation should be started, because

the

BusLeft >V

setpoint is used for healthy bus detection

(this condition applies only if

BusL Volt prot

is set to

ENABLED).
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  neutral  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BusL L12, L23 or L31 under

Left bus L12, L23 or L31 voltage was under the

BusLeft <V

limit for the

BusLeft V del

time

Information about that is

recorded into controller history.
Setpoint

BusL protect

BusL Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be over the

BusLeft

limit if BTB synchronisation should be started, because

the

BusLeft <V

setpoint is used for healthy bus detection

(this condition applies only if

BusL Volt prot

is set to

ENABLED)..
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  phase  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-PHASE.

BusL L12, L23 or L31 over

Left bus L12, L23 or L31 voltage was over the

BusLeft >V

limit for the

BusLeft V del

time

Information about that is

recorded into controller history.
Setpoint

BusL protect

BusL Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be below the

BusLeft

limit if BTB synchronisation should be started, because

the

BusLeft >V

setpoint is used for healthy bus detection

(this condition applies only if

BusL Volt prot

is set to

ENABLED).
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  phase  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-PHASE.

BusR L1, L2 or L3 under

Right bus L1,L2 or L3 voltage was under the

BusRight <V

limit for the

BusRight V del

time

Information about that is

recorded into controller history.
Setpoint

BusR protect

BusR Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be over the

BusRight

limit if BTB synchronisation should be started, because

the

BusRight <V

setpoint is used for healthy bus detection

(this condition applies only if

BusR Volt prot

is set to

ENABLED).
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  neutral  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BusR L1, L2 or L3 over

Right bus L1, L2 or L3 voltage was over the

BusRight >V

Содержание InteliGen NT













































Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды

ComAp InteliGen NT, Руководство по устранению неисправностей

Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды