ComAp InteliGen NT Скачать руководство пользователя | Manualshive

Страница: 7 / 44

background image

InteliGen

NT

, InteliSys

NT

, InteliMains

NT

– Troubleshooting Guide,

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp

– August 2018

7

IGS-NT Troubleshooting Guide.pdf

Unsuccessful controller programming

Procedure which is described in this chapter is part of the Boot Jumper Programming video which you
can watch here:

http://www.comap.cz/support/training/training-videos

It  is  necessary  to  use  the  boot  jumper  for  controller  programming  in  case  of  unsuccessful  controller
firmware  programming.  It  may  for  instance  happen  due  to  an  accidental  cable  disconnection,
computer  failure  or  remote  connection  drop  out.  If  controller  firmware  programming  was  not
successful,  it  is  not  possible  to  open  connection  to  a  controller,  it  does  not  respond  and  controller
screen is blank. In such case you need to use this procedure for controller programming:

1. Close connection to  controller and start GenConfig
2. Check communication port setting in GenConfig. Go to Options

– Select connection and select

the right communication port. It is necessary to use the RS232 (1) controller interface, boot jumper
programming does not work with the RS232 (2) or USB controller interface.

3. Go to File

– Firmware upgrade and Cloning… – FW upgrade (default configuration)… and select

firmware you would like to upload into a controller.
4. Follow instructions in the notification window:

«
...
5
6
7
8
9
...
»

Содержание InteliGen NT













































Отзывы:

Нет отзывов

Похожие инструкции для InteliGen NT

Бренд: Sole Diesel Страницы: 8

Бренд: Abicor Binzel Страницы: 8

Бренд: GBD Страницы: 68

Бренд: Kasco Страницы: 3

Бренд: C Prox Ltd Страницы: 5

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: RAKwireless Страницы: 6

Бренд: Sunnen Страницы: 24

Бренд: Aurora Страницы: 2

Snappi Pushchair

Бренд: Tendercare Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды