ComAp InteliGen NT Скачать руководство пользователя

Страница: 33 / 44

InteliGen

, InteliSys

, InteliMains

– Troubleshooting Guide,

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp

– August 2018

IGS-NT Troubleshooting Guide.pdf

IGS-NT Alarm/History

record

Alarm/

History

Appeara

nce

Description

during  synchronisation  and  you  may  need  to  adjust  their
setting.
Actual  state  of  synchronization  is  visible  on  the  controller
measurement screen with synchroscope where speed and
voltage  regulators'  outputs,  slip  frequency  and  generator
and  mains/bus  voltages  can  be  observed  during  the
synchronization process.

BOC L1, L2 or L3 under

A+H

Generator L1, L2 or L3 voltage was under the

Gen <V

BOC

limit for

Gen V del

time

Undervoltage protections

are based on

Gener protect

Gen <V BOC

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to neutral voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BOC L1, L2 or L3 over

A+H

Generator L1, L2 or L3 voltage was over the

Gen >V BOC

limit for

Gen V del

time

Overvoltage protections are

based on

Gener protect

Gen >V BOC

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to neutral voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

Sd L1, L2 or L3 over

A+H

Generator L1, L2 or L3 voltage was over the

Gen >V SD

limit for

Gen V del

time

Overvoltage protections are

based on

Gener protect

Gen >V SD

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to neutral voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BOC L12, L23 or L31 under

A+H

Generator L12, L23 or L31 voltage was under the

Gen <V

BOC

limit for

Gen V del

time

Undervoltage protections

are based on

Gener protect

Gen <V BOC

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to phase voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-PHASE.

BOC L12, L23 or L31 over

A+H

Generator L12, L23 or L31 voltage was over the

Gen >V

BOC

limit for

Gen V del

time

Overvoltage protections are

based on

Gener protect

Gen >V BOC

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to phase voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-PHASE.

Sd L12, L23 or L31 over

A+H

Generator L12, L23 or L31 voltage was over the

Gen >V

limit for

Gen V del

time

Overvoltage protections are

based on

Gener protect

Gen >V SD

and

Gen V del

setpoints. This alarm is issued if voltage protections are
based on phase to phase voltages. It means that

Basic

settings

FixVoltProtSel

is set to PHASE-PHASE.

BOC fgen under

A+H

Generator frequency was under the

Gen <f

limit for

Gen f

del

time

Under frequency protection is based on

Gener

protect

Gen <f

and

Gen f del

setpoints.

BOC fgen over

A+H

Generator frequency was over the

Gen >f

limit for

Gen f

del

time

Over frequency protection is based on

Gener

protect

Gen <f

and

Gen f del

setpoints.

BOC ReversePwr

A+H

This alarm is issued by the reverse power protection. This
protection is based on

Gener protect

Reverse power

and

ReversePwr del

setpoints. This alarm means that either

engine speed/power control does not work properly or

Содержание InteliGen NT













































Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды

ComAp InteliGen NT, Руководство по устранению неисправностей

Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды