ComAp InteliGen NT Скачать руководство пользователя

Страница: 42 / 44

InteliGen

, InteliSys

, InteliMains

– Troubleshooting Guide,

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp

– August 2018

IGS-NT Troubleshooting Guide.pdf

IGS-NT Alarm/History

record

Alarm/

History

Appeara

nce

Description

Overload

Genset overload protection was activated. See setpoints

Gener protect

OverldStrtEval

and

2POverldStEvDel.

Be aware that this protection is based on

Basic settings

Nominal power

setpoint setting.

Gen start

Indication of genset start using the Start button

Gen stop

Indication of genset stop using the Stop button

Gen MF start

Indication of genset start by the AMF function

Gen MF stop

Indication of genset stop by the AMF function

Gen Rem start

Indication of genset start using the Rem start/stop binary
input

Gen Rem stop

Indication of Gen-set stop using the Rem start/stop binary
input

Load Shed

Load Shedding function was activated and corresponding
LdShed stage x output was closed. See description of
setpoints in the

Load shedding

group of setpoints.

Load Reconnect

Load

Shedding

function

was

deactivated

and

corresponding LdShed stage x output was opened. See
description of setpoints in the

Load shedding

group of

setpoints.

VectorShift

Indication of VectorShift protection activation.
See setpoints

Mains protect

VectorS prot

and

VectorS

limit

Other CB trip

Other CB on bus was tripped. This information is available
for breakers which are controlled by a ComAp controller
(IG/IS-NT or IM-NT).

GCB opened

GCB was opened

GCB closed

GCB was closed

MCB opened

MCB was opened

MCB opened ext

MCB was opened externally

MCB closed

MCB was closed

MGCB opened

MGCB was opened

MGCB closed

MGCB was closed

BTB opened

BTB was opened

BTB opened ext

BTB was opened externally

BTB closed

BTB was closed

SyncStarted

Forward synchronization was started

RevSyncStarted

Reverse synchronization was started

Ready

Genset is ready to be started

Idle run

Engine was started (“engine started” conditions were
fulfilled) and engine speed and generator voltage goes up
to nominal values during the Idle run state.

Running

Genset is running and GCB can be closed or
synchronisation started.

Warming

Indication of Warming function activation. In case of
operation in parallel with mains is genset load reduced to

Warming load

level. For more information about this

function see setpoints

Engine params: Warming

load, Warming temp, Max warm time.

Soft load

Genset load is increased according to

Sync/Load ctrl

Load ramp

Load gain

Load int, RampStartLevel

setpoints

setting.

Loaded

Genset is loaded

Soft unload

Genset load is decreased according to

Sync/Load ctrl

Load ramp

Load gain

and

Load int

setpoints setting.

Содержание InteliGen NT













































Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды

ComAp InteliGen NT, Руководство по устранению неисправностей

Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды