ComAp InteliGen NT Скачать руководство пользователя

Страница: 36 / 44

InteliGen

, InteliSys

, InteliMains

– Troubleshooting Guide,

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp

– August 2018

IGS-NT Troubleshooting Guide.pdf

IGS-NT Alarm/History

record

Alarm/

History

Appeara

nce

Description

limit for the

BusRight V del

time

Information about that is

recorded into controller history.
Setpoint

BusR protect

BusR Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be below the

BusRight >V

limit if BTB synchronisation should be started,

because the

BusRight >V

setpoint is used for healthy bus

detection (this condition applies only if

BusR Volt prot

is set

to ENABLED).
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  neutral  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-NEUTRAL.

BusR L12, L23 or L31 under

Right bus L12, L23 or L31 voltage was under the

BusRight

limit for the

BusRight V del

time

Information about

that is recorded into controller history.
Setpoint

BusR protect

BusR Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be over the

BusRight

limit if BTB synchronisation should be started, because

the

BusRight <V

setpoint is used for healthy bus detection

(this condition applies only if

BusR Volt prot

is set to

ENABLED)..
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  phase  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-PHASE.

BusR L12, L23 or L31 over

Right bus L12, L23 or L31 voltage was over the

BusRight

limit for the

BusRight V del

time

Information about

that is recorded into controller history.
Setpoint

BusR protect

BusR Volt prot

has to be set to

ENABLED if healthy bus voltage detection and history
record are requested. Voltage has to be below the

BusRight >V

limit if BTB synchronisation should be started,

because the

BusRight >V

setpoint is used for healthy bus

detection (this condition applies only if

BusR Volt prot

is set

to ENABLED).
This  alarm  is  issued  if  voltage  protections  are  based  on
phase  to  phase  voltages.  It  means  that

Basic settings

FixVoltProtSel

is set to PHASE-PHASE.

BusL f under

Left bus frequency was under the

BusLeft <f

limit for

BusLeft f del

time

Under frequency protection is based on

BusL protect

BusLeft <f

and

BusLeft f del

setpoints.

BusL f over

Left bus frequency was over the

BusLeft >f

limit for

BusLeft

f del

time

Over frequency protection is based on

BusL

protect

BusLeft >f

and

BusLeft f del

setpoints.

BusR f under

Right bus frequency was under the

BusRight <f

limit for

BusRight f del

time

Under frequency protection is based

BusR protect

BusRight <f

and

BusRight f del

setpoints.

BusR f over

Right bus frequency was over the

BusRight >f

limit for

BusRight f del

time

Over frequency protection is based on

BusR protect

BusRight >f

and

BusRight f del

setpoints.

Vb L1, L2 or L3 under

Bus L1, L2 or L3 voltage was under the

Bus < Hst

limit for

Bus V del

time

Undervoltage protections are based on

Bus protect

Bus < Hst

and

Bus V del

setpoints. This

alarm is issued if voltage protections are based on phase

Содержание InteliGen NT













































Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды

ComAp InteliGen NT, Руководство по устранению неисправностей

Результаты поиска

Содержание InteliGen NT

Отзывы:

Похожие инструкции для InteliGen NT

Бренды по названию

Популярные бренды