13 von 36
Yale overload protection device
(optional)
The overload protection device is set to approx.
125% (±15%) of the nominal load. Its adjust-
ment must only be carried out by a competent
person or an authorised service partner.
When the load limit is exceeded, the overload
protection device is activated and prevents
lifting of the load by the hand chain wheel
slipping.
INSPECTIoN, MAINTENANCE AND
rEPAIr
According to national and international acci-
dent prevention and safety regulations hoisting
equipment must be inspected:
• in accordance with the risk assessment of
the operating company
• prior to initial operation
• before the unit is put into service again
following a shut down
• after substantial changes
• however, at least once per year, by a
competent person.
ATTEnTion:
Actual operating conditions (e.g.
operation in galvanizing facilities) can dictate
shorter inspection intervals.
Repair work may only be carried out by a spe-
cialist workshop that uses original Yale spare
parts. The inspection (mainly consisting of a
visual inspection and a function check) must
determine that all safety devices are complete
and fully operational and cover the condition
of the unit, suspension, equipment and sup-
porting structure with regard to damage, wear,
corrosion or any other alterations.
Initial operation and recurring inspections
must be documented (e.g. in the CMCO works
certificate of compliance). See also the main-
tenance and inspection intervals on page 32.
If required, the results of inspections and ap-
propriate repairs must be verified. If the hoist
(from 1 t lifting weight) is fitted on or in a trolley
and if the hoist is used to move a lifted load
in one or several directions, the installation
is considered to be a crane and the further
inspections must be carried out, as required.
Paint damage should be touched up in order to
avoid corrosion. All joints and sliding surfaces
should be slightly greased. In the case of heavy
contamination, the unit must be cleaned.
The unit must be given a general overhaul
after 3 years, at the latest.
In particular, check the dimensions of the
load chain, the load hook and the top hook.
They must be compared with the dimensions
specified in the table (Tab. 2, Tab. 3).
ATTEnTion:
After the replacement of
components, a subsequent inspection by a
competent person is obligatory!
Inspection of the load chain
(acc. to DIN 685-5)
Load chains must be inspected for mechanical
damage at annular intervals, however
after
50 operating hours
, at the latest. Inspect the
load chain for sufficient lubrication and check
for external defects, deformations, superficial
cracks, wear and corrosion marks.
Round steel section chains must be replaced
when the original nominal thickness ´d´ on
the chain link with the worst wear has been
reduced by more than 10% or when the chain
has elongated over one pitch ´p
n
´ by 5 %
(Fig. 16) or over 11 pitches (11 x p
n
) by 3 %.
Nominal dimensions and wear limits are
shown in table 2. If one of the limit values is
reached, the load chain must be replaced.
Maintenance of the load chain
In most cases, chain wear in the link points
is caused by insufficient care of the chain. In
order to ensure optimal lubrication of the link
contact points, lubricate the chain at regular
intervals adapted to the application with creep-
type lubricant (e.g. gear oil).
A dry film lubricant, e.g. PTFE spray, should
be used in environments where abrasives like
sand, etc., occur.
The service life of the load chain can be in-
creased by careful lubrication to 20 - 30 times
compared with a chain that is not serviced.
- When lubricating the chain, make sure the
chain is in no-load condition so that the oil
can reach the contact points of the chain
links which are subject to wear. Chain link
parts contacting each other must always be
coated with lubricant, otherwise increased
wear on the chain results.
- It is not sufficient to lubricate the chains on
the outside as this does not ensure that a
lubricant film can build up in the contact
points.
- With a constant lifting path of the chain, the
change-over area from lifting to lowering
movement must be checked in particular.
- Make sure that the load chain is lubricated
over its entire length, also including the part
of the chain in the housing of the hoist.
- Clean dirty chains with petroleum or a similar
cleaning agent, never heat the chain.
- When lubricating the chain, also check the
chain for wear.
ATTEnTion:
It must be ensured that no lub-
ricant can penetrate into the brake enclosure.
This may result in failure of the brake.
replacing the load chain
The load chain must be replaced by a new
chain of the same dimensions and quality in
the event of visible damage or deformations,
however, when the discarding status has been
reached, at the latest.
A load chain to be discarded must only be
replaced by an authorized specialist workshop.
Only fit load chains which have been approved
by the manufacturer. Non-compliance with this
specification will render the legal warranty or
guarantee void with immediate effect.
note:
Replacement of a load chain must be
documented!
ATTEnTion:
Chains must only be replaced
by chains of the same material, with the same
quality and the same dimensions.
Hoist with single fall
- Only pull in the new chain in no-load condi-
tion.
- An open load chain link is required as a
tool. It can be obtained by using an abrasive
wheel to cut a section from an existing link
with the same dimension. The length of the
cut section must at least correspond to the
thickness of the link.
- Remove load hook from the old load chain
and suspend open load chain link in the
loose end of the load chain.
- Suspend the new lubricated load chain
also in the open link and pull it in (chain
movement UP).
- Do not fit a twisted chain. The welds must
face outwards from the chain wheel.
- When the old load chain has passed through
the hoist unit it can be detached together
with the open chain link and the load hook
can be fitted on the new load chain just
pulled in.
- Fix the end of the idle fall of the new load
chain on the housing or frame (depending
on model) of the hoist.
Hoist with several falls
ATTEnTion:
Only pull in the new chain when
the bottom block is unloaded, otherwise the
bottom block may drop when the load chain
is detached. Danger of injury!
- An open load chain link is required as a
tool. It can be obtained by using an abrasive
wheel to cut a section from an existing link
with the same dimension. The length of the
cut section must at least correspond to the
thickness of the link.
- Detach the loaded-fall end of the load chain
from the housing of the hoist unit or the
bottom block (depending on model).
- Suspend prepared, open load chain link in
the now free load chain end.
