Colop digital e-mark create Скачать руководство пользователя страница 9

Страница: 9 / 60

e-mark create marking device

Chapter 2 Safety

CODI Standard 1.0

9/60

Operating and Maintenance Manual

AFETY

This documentation is structured in accordance with valid EU directives and contains safety notices. The user of the

e-mark create is responsible for complying with safety-related information in this documentation. This section

contains a general description of the warning and safety instructions, and important safety notices.

2.1 Signal words used in safety notices

DANGER!

A safety notice with the signal word

DANGER

points to

an immediately threatening

hazard

to the life and limb of people!

This signal word denotes a hazard with a high level of risk which, if not avoided, can

result in death or serious injury.

WARNING!

A safety notice with the signal word

WARNING

denotes a

dangerous situation

that

could cause personal injury (of a serious nature) and may also cause damage to items

of capital equipment!

This signal word denotes a hazard with a moderate level of risk which, if not avoided,

can result in death or serious injury.

CAUTION!

A safety notice with the signal word

CAUTION

denotes a

potentially hazardous

situation

that can result in slight injuries or damage to items of capital equipment!

This signal word denotes a hazard with a low level of risk which, if not avoided, can

result in minor or moderate injury.

NOTICE

A safety notice with the signal word

NOTICE

denotes a situation that could result in

damage to items of capital equipment!

This signal word denotes a hazard which, if not avoided, can result in damage to

items of capital equipment or damage to the device.

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды