Colop digital e-mark create Скачать руководство пользователя страница 43

Страница: 43 / 60

e-mark create marking device

Chapter 5 Operation

CODI Standard 1.0

43/60

Operating and Maintenance Manual

5.7 WIFI connection

If instructions on the wizard are followed when installing the app, the WIFI connection is set up and the software

automatically connects with the device when required. Several devices can also be added and one of them selected

from a list.

In the event the connection set up via the app is unsuccessful, the WIFI connection can also be set up manually via

the settings on a computer, smartphone or tablet. The e-mark create must be switched on.

Select the SSID on your e-mark create in the WIFI settings on your mobile device, click "Connect" and enter the

password. The actual illustration of the activated WIFI connection depends on the mobile device and the software

installed and may differ from the example illustration below.

Fig. 35: Example image of WIFI connection in the settings of the mobile device

The e-mark create is now connected by WIFI to the mobile device. This means that the e-mark create will not

disconnect automatically when closing the app. The connection has to be disconnected manually in the WIFI

settings on your mobile device.

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды