Colop digital e-mark create Скачать руководство пользователя страница 14

Страница: 14 / 60

e-mark create marking device

Chapter 2 Safety

CODI Standard 1.0

14/60

Operating and Maintenance Manual

2.4 General safety instructions and regulations

Without exception, observe the following safety provisions and obligations when working at or on the product:



Always operate the product in operationally perfect and clean condition.



It is prohibited to convert or modify the product.



Faults must be remedied immediately.



Always use genuine spare parts for repair work or when replacing damaged components.



Always pay careful attention to the safety notices and operating instructions.

2.5 Safety notices on the product

Safety notice panels are fitted to the product to draw attention to potential hazards. Always pay attention to and

comply with the safety designation instructions on the product. During the service life of the product, if the safety

designation label fades or gets damaged, you must shut down the product.

The pictograms for warnings, prohibitions and stipulations on the product, together with their meaning:

Pictograms

Location

Designation

Description

Underside

Marking device

Warning: hot surface.

The print head surface may become hot. Do not

touch the print head!

Underside

Marking device

Prohibition: Do not

touch.

Do not touch the print head!

Battery,

cartridge,

e-mark create

Indications on

disposing of electronic

waste

Dispose of the appliance in accordance with

legislation and recycle wherever possible.

Battery

Indications on handling

batteries

Do not disassemble or modify, do not short-

circuit, do not dispose in fire and do not expose

to high temperature

Do not disassemble

or modify

Do not short-circuit

Do not dispose in fire

Do not expose to high

temperature

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды