Colop digital e-mark create Скачать руководство пользователя страница 8

Страница: 8 / 60

e-mark create marking device

Chapter 1 Introduction

CODI Standard 1.0

8/60

Operating and Maintenance Manual

Target groups and previous knowledge

Users of the e-mark create are non-professionals, aware of the hazards associated with using the device via the

safety pictograms on the e-mark create and instructions in the Quick Setup Guide and in this Operating and

Maintenance Manual. Users are able to recharge the e-mark create with the power adapter (supplied) and replace

ink cartridges. Users are not authorized to carry out repairs on the product.

Inspection and maintenance and/or repairs must only be carried out by qualified electricians.

The content and purpose of this documentation

Users can download this original Operating and Maintenance Manual at

https://emark.colop.com/usermanual

for

information.

This documentation contains the relevant information for e-mark create assembly, commissioning, operation,

maintenance and disposal. This documentation is intended to ensure hazard-free work with the e-mark create.

Compliance with the instructions contained within this document enables hazard-free working and avoids damaging

the e-mark create.

Limits of use

The limits of use for the e-mark create are defined as follows:



The device is intended for use in enclosed, clean and dry areas (offices, warehouses, private residences)



Horizontal place of use on level, firm ground



Ambient temperature: +15 °C to +35 °C



Humidity range 5 % to 100 % (storage 5 % to 80 %)



The e-mark create is a marking device to print imprints sent via a software application



It can print directly onto a variety of absorbent surfaces including standard paper, cardboard, fabric, wood,

cork, dry wall, high-gloss paper, photo paper and other surfaces with special coatings.



The e-mark create is fitted with an LED light strip.



The rechargeable battery of the e-mark create is recharged using the power plug.

1.4 Principle

This product incorporates state-of-the-art technology and complies with applicable health and safety regulations.

Nonetheless, the following hazards can arise as a result of incorrect transport, improper use, or failure to observe

the safety instructions contained in this Operating and Maintenance Manual or in the event of misuse:



fatal or serious injury to users or third parties



damage to the product and other items of capital equipment



impairment to the efficient operation of the product

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды