Colop digital e-mark create Скачать руководство пользователя страница 12

Страница: 12 / 60

e-mark create marking device

Chapter 2 Safety

CODI Standard 1.0

12/60

Operating and Maintenance Manual

WARNING!

Hazard from damaged electrical components or damaged insulation.

In the event the device, housing or insulation is damaged, stop using the device and

have it tested and repaired by an electrician or the manufacturer's customer service.

WARNING!

Hazard from rechargeable batteries (short-circuit, overheating, fire).

- Do not expose lithium batteries to heat, cold or water (do not leave in direct sunlight

or charge or store outdoors).

- Do not (forcibly) open or expose to large impacts or shocks.

- Only use charging systems as recommended by the manufacturer.

- The manufacturer's safety instructions must be complied with throughout the entire

disposal process.

- Battery contacts (outside the device) must not come into contact with metallic objects

such as coins or keys to prevent a short circuit.

- The marking device and/or rechargeable battery must never get wet.

- Burning batteries can cause blow-outs, causing a battery to be blown away. Battery

fires give off extremely thick, particularly toxic smoke.

- Following extended periods in storage or before taking to a collection point, the poles

on lithium rechargeable batteries should be covered with adhesive tape to prevent

short circuits. Maximum protected storage, e.g. in the original packaging and quick

deposit in a collection point are recommended.

- Visually damaged, overheated or blown out batteries must not be reused and must

not be stored in the house, flat or garage.

WARNING!

Hazard posed by improper use.

Read the Operating Manual before switching on the device. Pay attention to all safety

notices. The Operating Manual must be kept!

CAUTION!

Hazard from hot surfaces.

Immediately after using the e-mark create, certain parts can be hot. Do not touch the

print head on the underside of the marking device. Leave to cool before replacing.

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды