Colop digital e-mark create Скачать руководство пользователя страница 35

Страница: 35 / 60

e-mark create marking device

Chapter 5 Operation

CODI Standard 1.0

35/60

Operating and Maintenance Manual

Light Guide

Designation

Description

LED 1, 7

Red double flashing of all

lights and sounds

Warning: cartridge is drying

out

The e-mark create must be

returned to the docking station

immediately

LED 8, 9

green flashing light

(left or right side)

During printing mode

Printing to the right or left side. A

short signal sounds when the

end of the imprint has been

reached

LED 3, 5 ,2, 6

green light

Ready to print

The e-mark create has been

removed from the docking

station and powered up.

Ready for printing.

No lights

e-mark create switched off

Battery empty

Battery contacts are covered

Sleep mode

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды