Colop digital e-mark create Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 60

background image

e-mark create marking device

Chapter 6 Maintenance

CODI Standard 1.0

50/60

Operating and Maintenance Manual

Fig. 44: Pull out ink cartridge

NOTICE

Always press open the lower panel first, otherwise the ink cartridge cannot be removed

without damaging the e-mark create!

8.

Remove the new ink cartridge from the packaging and dispose of the packaging responsibly.

9.

Pull out the strip from the print head and dispose of responsibly.

Fig. 45: Ink cartridge

New original ink cartridges available from your distributors.

10. Insert new ink cartridge.

-

Press towards the front end of the compartment.

-

Cartridge snaps in.

Fig. 46: Insert ink cartridge

«
...
48
49
50
51
52
...
»

Содержание digital e-mark create





























































Отзывы:

Нет отзывов

Похожие инструкции для digital e-mark create

Бренд: U-Line Страницы: 48

Бренд: U-Line Страницы: 32

Бренд: Saeco Страницы: 52

Бренд: Nespresso Страницы: 36

Бренд: Wolfgang Puck Страницы: 18

Бренд: Bunn Страницы: 16

Бренд: Schaerer Страницы: 2

Бренд: Dymo Страницы: 36

Бренд: SEVERIN Страницы: 1

2 lb. EXPRESSBAKE recip

Бренд: Oster Страницы: 76

Бренд: La San Marco Страницы: 36

BELGIAN WAFFLE BOAT MAKER

Бренд: Villaware Страницы: 9

Oracle Touch SES990BST

Бренд: Sage Страницы: 27

Бренд: KING Страницы: 17

Бренд: Frigidaire Страницы: 9

Бренд: Whirlpool Страницы: 9

Бренд: STARFRIT Страницы: 20

Бренд: RTC Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды