CNC Seig X2 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 35

background image

Y axis adjustment

1. Using the drill and coupling again, slowly move the Y axis back and forth. Apply grease as before.
2. Move the table all the way to the front of the machine. Tighten the stepper mount.
3. Now move the Y axis away from the operator and towards the column. Tighten the Y axis ball nut mount bolt

located at the front of the Y axis cross slide casting in the center near the bottom.

4. Again, move the axis forward and backwards several times tightening the bolts a little more each time.
5. The Y axis should not be ready to install your stepper motor.

Axis Adjustment Procedure for X and Y

«
...
32
33
34
35
»

Содержание Seig X2




































Отзывы:

Нет отзывов

Похожие инструкции для Seig X2

Бренд: 3M Страницы: 11

Бренд: TDK-Lambda Страницы: 29

Бренд: ODA Страницы: 113

Бренд: ABS Страницы: 8

Бренд: Gage Bilt Страницы: 12

Бренд: Gage Bilt Страницы: 13

Бренд: Gage Bilt Страницы: 9

Бренд: Gage Bilt Страницы: 10

DC POWER-L Series

Бренд: Salicru Страницы: 32

Бренд: TE Connectivity Страницы: 8

Бренд: H3C Страницы: 5

Бренд: Tohnichi Страницы: 28

Бренд: Mannesmann Demag Страницы: 27

Бренд: Ferm Industrial Страницы: 46

Бренд: Paslode Страницы: 24

Бренд: Skil Страницы: 128

Бренд: Silverline Страницы: 3

Бренд: Maggi Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды