CNC Seig X2 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 35

background image

Note: VERY IMPORTANT!!!! The dovetails on the table are offset
from the center of the table top as shown here.

The table end plates can be installed either way, and, differently
at each end of the table. The large hole in the table end plate is off
set to match the dovetails but the holes that mount it to the table
are in the center of the table. Therefore, the end plates can be
installed incorrectly. Please make sure that they are aligned
correctly on BOTH ENDS or the ball screw will be out of alignment
and binding and interference will occur!!!!

Correct

Incorrect

NOTE: TABLE FRONT IS IDENTIFIED BY HAVING A MEASUREING SCALE ON IT!!!!!

«
...
22
23
24
25
26
...
»

Содержание Seig X2




































Отзывы:

Нет отзывов

Похожие инструкции для Seig X2

Бренд: jbc Страницы: 12

Бренд: Tohnichi Страницы: 28

Alligator Staple Gold Class

Бренд: Flexco Страницы: 2

DIMENSION CS Series

Бренд: Puls Страницы: 27

Бренд: ROCKSOLAR Страницы: 12

Бренд: Parker Страницы: 6

Бренд: FDT Страницы: 4

Бренд: InWin Страницы: 15

MICRO-Router MOF

Бренд: Proxxon Страницы: 16

Бренд: Cleco Страницы: 42

Бренд: Rebel Страницы: 2

Бренд: TDK-Lambda Страницы: 24

Бренд: Sealey Страницы: 2

Бренд: Fein Страницы: 118

Бренд: Facom Страницы: 2

Бренд: B&K Страницы: 2

Бренд: Milwaukee Страницы: 13

Бренд: SATA Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды