background image

6.0 

Warranty and Guarantee 

 

The legal warranty applies. 
 
Warranty for the kit 

We guarantee 6 months warranty on the kit. 
The guarantee includes the free repair of the defects, which are demonstrably due to the use of 
non-flawless material or manufacturing faults. 
Since we have no influence on the correct and proper construction, for understandable reasons we 
can only assume the guarantee of the completeness and perfect condition of the components. 
The corresponding function of the components in the non-installed state and the adherence to the 
technical data of the circuit is guaranteed in accordance with the soldering regulations, professional 
processing and the required commissioning and operation. Further claims are excluded. 
We do not accept any liability for any damages or consequential damages in connection with this 
product. 
We reserve the right to repair, remedy, spare parts delivery or refund of the purchase price. The 
following criteria do not repair or void the warranty claim: 

 

● When soldering acid-containing solder, soldering or acidic 
● Flux, etc. was used. 
● If the kit was incorrectly soldered and built. 
● Incorrect operation or treatment. 
● Improper maintenance and repair by third parties. 
● Technical changes by third parties. 

 
 

7.0 Disposal 

 
If the appliance is to be disposed of, it must not be thrown into the household waste. 
These must then be disposed of at collection points, where televisions, computers 
etc. can be delivered (please inquire at your local office or in the 
Municipal administration According to these electronic waste collection points). 
 

Содержание AC-CNC2017-2S

































Отзывы: