Climax BB7100 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 130

background image

P/N 55769, Rev. 4

Page 5

RISK ASSESSMENT CHECKLIST

The following checklist is not intended to be an all-inclusive list of things
to watch out for when setting up and operating this Portable Machine Tool.
However, these checklists are typical of the types of risks the assembler
and operator should consider. Use these checklists as part of your risk
assessment:

T

ABLE

1-1. R

ISK ASSESSMENT CHECKLIST BEFORE SET

-

UP

Before set-up



I took note of all the warning labels on the machine.



I removed or mitigated all identified risks (such as tripping, cutting, crushing,
entanglement, shearing, or falling objects).



I considered the need for personnel safety guarding and installed any necessary
guards.



I read the machine assembly instructions.



I created a lift plan, including identifying the proper rigging, for each of the setup
lifts required during the setup of the support structure and machine.



I located the fall paths involved in lifting and rigging operations. I have taken pre-
cautions to keep workers away from the identified fall path.



I considered how this machine operates and identified the best placement for the
controls, cabling, and the operator.



I evaluated and mitigated any other potential risks specific to my work area.

T

ABLE

1-2. R

ISK ASSESSMENT CHECKLIST AFTER SET

-

UP

After set-up



I checked that the machine is safely installed and the potential fall path is clear. If
the machine is installed at an elevated position, I checked that the machine is
safeguarded against falling.



I identified all possible pinch points, such as those caused by rotating parts, and
informed the affected personnel.



I planned for containment of any chips or swarf produced by the machine.



I followed the required maintenance with the recommended lubricants.



I checked that all affected personnel have the recommended personal protective
equipment, as well as any site-required or regulatory equipment.



I checked that all affected personnel understand and are clear of the danger zone.



I evaluated and mitigated any other potential risks specific to my work area.

«
...
11
12
13
14
15
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: Bartscher Страницы: 22

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: Fisher Scientific Страницы: 42

Бренд: Abicor Binzel Страницы: 92

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Cadex Страницы: 300

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды