Climax BB7100 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 130

background image

P/N 55769, Rev. 4

Page 29

OPERATION

Pre-start checks

WARNING

When setting up or servicing the machine, disconnect the
power source and lock the machine out. Failure to do so
could result in the machine being accidentally turned on,
and seriously injuring you and others.

Before operating the machine:

1.

Tie down the rotational drive unit torque arms and the axial feed unit stop rod.

2.

Ensure the rotational drive unit is filled with drive oil.

3.

Check that all cutters are sharp and in good condition.

4.

Secure all machine parts, including the axial tool carrier, tool head and cutting tool.
Check that moving parts move freely.

5.

Check that electric cords and cables are in good condition and correctly connected.

6.

Turn the hydraulic power unit OFF.

7.

Check that the hydraulic power unit wiring matches the electric power source. Plug
the power unit into a grounded outlet.

8.

Check the hydraulic power unit reservoir level. Fill the reservoir to above the red bar
with Mobil DTE-24 anti-wear hydraulic oil or equivalent. Check that the power unit
is on a level surface.

9.

Clean the hydraulic hoses and fittings before connecting them.

10.

Check that the hydraulic power unit pump motor is rotating as directed by the arrow
on the pump/motor coupling.

Starting the machine

The CLIMAX BB7100 is intended for operation at varying rates of rotation and feed. The
rotation speed is controlled by varying the output from the Hydraulic Power Unit (HPU).
The feed rate of the mechanical unit is controlled manually from the feed unit.

If boring:

Set the feed direction on the axial feed.
Set the feed rate on the axial feed

If facing:

Set the feed direction on the axial feed to NEUTRAL.
Lock the tool carrier to the bar using adjustable shoes.

«
...
35
36
37
38
39
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренд: Garden Treasures Страницы: 2

Бренд: XpressFill Страницы: 11

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Implantmed SI-1010

Бренд: W&H Страницы: 2

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: Unika Страницы: 8

Бренд: PMK Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды