Climax BB7100 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 130

background image

P/N 55769, Rev. 4

Page 1

GENERAL SAFETY GUIDELINES

The primary challenge for most on-site maintenance is that repairs are often done under difficult
conditions.
CLIMAX Portable Machining & Welding Systems leads the way in promoting the safe use of
portable machine tools. Safety is a joint effort. As the operator of this machine, you are expected
to do your part by closely examining the job site and following the operating procedures outlined
in this manual, your own company rules, and local regulations.

WARNING

For maximum safety and performance, read and understand this entire
manual and all other related safety instructions before using this
equipment. Failure to follow the instructions and guidelines in this manual
could cause personal injury, fatalities and property damage.

Qualified Personnel

Before  operating  this  machine,  you  must  receive
training  specific  to  this  machine  from  a  qualified
trainer.  Do  not  operate  the  machine.  If  you  are  not
familiar with the proper and safe operation.

Obey Warning Labels

Obey  all  warning  labels.  Failure  to  follow  instructions
or  heed  warnings  could  result  in  injury,  or  even  be
fatal.  Proper  care  is  your  responsibility.  Contact
CLIMAX  immediately  for  replacement  manuals  or
safety decals.

Intended Use

Use  this  machine  according  to  the  instructions  in  this
operating  manual.  Do  not  use  this  machine  for  any
purpose  other  than  its  intended  use  as  described  in
this manual.

Stay Clear of Moving Parts

Keep clear of the machine during operation. Never
lean toward or reach into the machine to remove chips
or to adjust the machine while it is running.

Rotating Machinery

Rotating machinery can seriously injure an operator.
Lock out all power sources before you interact with the
machine.

Keep Your Work Area Clean and Tidy

Keep all cords and hoses away from moving parts
during operation. Do not clutter the area around the
machine.

Secure Loose Clothing and Long Hair

Rotating machinery can cause serious injuries. Do not
wear loose fitting clothing or jewelry. Tie back long
hair or wear a hat.

Hazardous Environments

Do not use the machine near explosive chemicals,
toxic fumes, inappropriate radiation hazards or other
hazardous environments.

Flying Chips

Flying metal chips can cut or burn. Do not remove
chips until after the machine has been locked out, all
power sources are off and the machine has stopped.

«
...
7
8
9
10
11
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: Makerfire Страницы: 10

Бренд: Taber Страницы: 27

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Sagola Страницы: 8

Бренд: Canta Страницы: 2

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: FJC Страницы: 2

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: Panlux Страницы: 2

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды