Climax BB7100 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 130

background image

Page 2

BB7100 Operating Manual

MACHINE SPECIFIC SAFETY PRACTICES

All aspects of the machine have been designed with safety in mind. Following are safety practices
that you should keep in mind when using the CLIMAX BB7100 Boring Machine.

Personal Protective Equipment (PPE)

Eye and hearing protection must be worn while using
the machine. These safety items do not impose
constraints to the safe operation of the machine.

Operating Conditions

Do not operate the machine if it is not mounted to the
workpiece as described in this manual.

Tooling

The machine is provided with all the tools for the setup
and operation of the machine.

Lifting

Avoid lifting heavy objects by yourself as serious injury
can result. Always follow your plant’s procedures for
lifting heavy objects.

Cutting Fluids

Use only recommended lubricants or similar
equivalent when performing maintenance tasks. See
the “Maintenance” section for more information.

Danger Zone

The operator and other persons can be anywhere in
the vicinity of the machine. The operator must ensure
there are no other persons in danger from the
machine.

Clamp Collars

To  prevent  the  bar  from  sliding  through  the  support
bearings,  or  falling,  use  P/N  42792  –  The  collars  are
made  in  matching  sets  and  must  be  used  to  secure
the bar when the machine is in the vertical orientation.
Torque these collars to 46 ft-lbs. Use the clamp collars
to  prevent  over  tightening  of  the  bearings.  Clamp
collars should be positioned ABOVE at least 2 support
bearings when installed in a vertical orientation. Clamp
collars should be shouldered against the bearing when
in use.

Metal Fragment Hazard

The machine dispenses metallic fragments during
normal operation. You should wear eye protection and
gloves at all times when working with the machine.

Hazardous Environments

Do not use the machine in a hazardous environment,
such as near explosive chemicals, toxic fumes, or a
radiation hazard.

Radiation Hazards

There are no systems or components on this machine
that are capable of producing hazardous EMC, UV or
other radiation hazards. The machine does not use
lasers nor does it create hazardous materials such as
gasses or dust.

Adjustments and Maintenance

All adjustments, lubrication and maintenance should
be done with the machine stopped, and disconnected
from power. The shut-off valve should be locked and
tagged out before any maintenance occurs.

Warning Labels

Warning labels are attached to your machine upon
delivery. If any labels are defaced or missing, be sure
to contact CLIMAX immediately for replacements.

Maintenance

Be sure the machine components are free of debris
and properly lubricated prior to use.

«
...
8
9
10
11
12
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: Hanil Страницы: 60

Бренд: Zetec Страницы: 23

Бренд: NEC Страницы: 54

Бренд: NAD Страницы: 10

Бренд: UFO Страницы: 16

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

Бренд: Tascam Страницы: 3

Бренд: Fast Страницы: 60

Бренд: A.J.Antunes Страницы: 24

Бренд: B&G Страницы: 2

Бренд: Garmin Страницы: 41

Бренд: Sagitter Страницы: 12

Бренд: Invacare Страницы: 271

Бренд: Delfield Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды