Climax BB7100 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 130

background image

Page 24

BB7100 Operating Manual

Micro Adjustment Boring Head

The micro-adjust boring head offers the possibility to micro-adjust readily available off-the-
shelf square shank tooling for boring. The micro-adjust travel is 0.5", and the ability to slide
the tool without having to change the setup provides a total tool travel of more than 2" (per
setup).

To set the tool to the desired diameter, simply feed the dial screw until reaching it and then
lock the middle dove tail set screw with the provided T handle hex drive. Each division in
the dial screw resolves in 0.001" change in diameter. The dove tail adjustment set screws are
set to the correct load by CLIMAX and should not be necessary to re-adjust them. These set
screws have Vibratite-VC3 in order to avoid losing tension during vibration. The lock also
has this compound, and it might be necessary to re-apply some every once in a while, if
necessary.
The BB7100 micro-adjustment boring head comes with a 3/4" square shank tool holder. A
bolt-on shim is provided the 3/4 tool holder so that it can be easily converted to a 1/2" tool
holder.
To set up leading and trailing, simply shift the boring heads against the mounting screws in
opposite directions.
There is a small set screw that stops the tool carriage from being removed from its holder,
and the boring head should never be operated without it on.
Proper maintenance would involve cleaning and lubricating the dove tail surfaces and the
dial screw threads and groove, and if the lock set screw feels loose after a while, applying
the provided Vibrative vc-3.

«
...
30
31
32
33
34
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: fadini Страницы: 20

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: P-Q Controls Страницы: 5

Бренд: P+L Systems Страницы: 2

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: JBM Страницы: 12

Бренд: Garmin Страницы: 41

Бренд: Landoll Страницы: 144

Бренд: Castellini Страницы: 299

Бренд: Lowenstein Medical Страницы: 457

GrainLogix XLB10

Бренд: LOFTNESS Страницы: 104

Бренд: AVID LABS Страницы: 20

Бренд: Briteq Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды