Climax BB7100 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 130

background image

Page 20

BB7100 Operating Manual

8.

Slide the bar drive lock ring back into place in the rotational drive. Tighten the clamp
screws on both lock rings.

CAUTION

Tighten only the six clamping socket-head cap screws
in the bar drive locking rings, not the jacking screws.
The jacking screws loosen the locking rings. Back out
the jacking screws before clamping the rings to avoid
damaging the rings.

9.

Slide the bar drive lock ring back into place in the rotational drive.

10.

Tighten the clamping screws on both lock rings.

WARNING

Weak tie down failure or loose torque arms can allow
the torque arms to swing uncontrollably, seriously
injuring the operator and damaging the machine.
Secure the torque arms to a stationary object strong
enough to withstand the full torque.

11.

Connect the hydraulic lines between the motor and the hydraulic power unit.

CAUTION

To avoid damaging the hydraulic power unit pump,
connect the hydraulic motor to the power unit before
plugging in and turning on the power unit.

«
...
26
27
28
29
30
...
»

Содержание BB7100



































































































































Отзывы:

Нет отзывов

Похожие инструкции для BB7100

Бренд: JB-Lighting Страницы: 60

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Modulate Страницы: 2

Бренд: XanLite Страницы: 4

Бренд: IBS Scherer Страницы: 64

Бренд: Yamaha Страницы: 45

Бренд: Pixlip Страницы: 15

AtLite Sure-Lites SELDWA29SD

Бренд: Eaton Страницы: 4

Бренд: Xils lab Страницы: 31

Бренд: Car Solutions Страницы: 24

Advisor Guide Pedestrian Signal

Бренд: Campbell Страницы: 14

Бренд: Handicare Страницы: 18

Бренд: Nakamichi Страницы: 12

Бренд: Qdot Страницы: 6

Бренд: SafeWaze Страницы: 2

Naturally Better

Бренд: RoboSol Страницы: 2

Бренд: RAMVAC Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды