manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 9

9

FieldSmart

®

 FxDS Frame

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 012010 REV H - July 2018

Using the isolation pad as a template, mark on the panel(s) of the raised floor the 4 holes where the frame is going to 

be secured to the floor. Using a 5/8” drill bit, drill a hole through each of the oblong marks you made with the isolation 

pad.

Take the threaded rods from the raised floor mounting kit and slide one through each of the holes. Using a hammer 

and holding them perpendicular to the floor, tap on the end firmly. The goal is to make a “mark” on the concrete floor 

visible enough to see where the 4 holes should be drilled.

Once the concrete floor is marked, remove the threaded rods and floor panels. Using a 5/8” masonry bit, drill the four 

required holes to a minimum depth of 2” (approx. 50mm).

Note: 

If for some reason you have trouble drilling the 5/8” hole, we 

recommend first drilling a 1/4” pilot hole before drilling out to 5/8”.

Thoroughly clean the dust from each hole, using a vacuum or blowout 

air bulb.

Note: 

To not degrade the anchor’s installed performance, any unused 

anchor holes (or other nearby holes) in the concrete within 3” must be 

filled with an epoxy filler (pour stone) or equivalent. Filled holes must be fully cured before anchors are installed and 

torqued.

19” Frame

9 

5

/

8

”

22”

1.

2.

3.

4.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды