manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 14

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

14

FieldSmart

®

 FxDS Frame

Installation Manual 

 _________________________________________________________

Manual 012010 REV H - July 2018

End Guard Support Bars

Once the interbays and end guards are mounted you can add the end 

guard supports bars. These may also be called crossover or stabilizing 

bars.

These are held in place by a female hinge piece which must be installed 

in the inside of the end guard, and a male hinge piece which comes 

pre-installed to the support bar. 

The support bars will be installed at the top and bottom of the front and 

back of the end guards.

Note: 

To install the female hinge piece, you must have access to the 

outside of the end guards. If the frame is to be installed with the end guard 

against a wall or another frame, these must be installed prior to floor 

mounting.

Hinge Mounting 

Screws

Female Hinge

Male Hinge

1.

2.

3.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды