manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 16

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

16

FieldSmart

®

 FxDS Frame

Installation Manual 

 _________________________________________________________

Manual 012010 REV H - July 2018

Adjusting the Doors

To adjust the doors, first align the 

doors so that there is an even gap 

around 1/8” from the top of the doors 

to the bottom. 

This can be done by adjusting the 

screws which hold the hinges to the 

end guards. 

Start with the screw in the center of 

the slot as most applications will not 

need adjustment afterward.

After the horizontal adjustments have 

been made, adjust the doors to be 

even vertically. 

This is done by locking down the 

higher door and then adjusting the 

lower door to match.

Grounding

Clearfield provides a ground bar with the FxDS which can be 

installed on the frame. Ground per your local rules and practices.

Adjustment plates will allow you to ensure that an even spacing between the doors is maintained from top to bottom. 

Vertical adjustments will be made with the door adjustment plate, while horizontal adjustments will be made with the 

end guard plate.

1.

2.

3.

4.

5.

6.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды