manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 18

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

18

FieldSmart

®

 FxDS Frame

Installation Manual 

 _________________________________________________________

Manual 012010 REV H - July 2018

Cable Mounting and Routing

Choose a green cable clamp that is close to the same size but slightly 

bigger than the cable you plan to mount. The difference in size can be 

made up by either wrapping the cable with some of the provided grommet 

tape, or laying a small strip of grommet tape in the bottom side of the cable 

clamp shell.

Note: 

The angle of cable mounting can be adjusted by pivoting the bracket 

on one of the mounting holes and securing it down with the other. A greater 

range of angles can be achieved by flipping the bracket to the other side.

Each panel comes with two types of cable mounting brackets. One is used for applications where you have access to 

pre-drilled and tapped holes in the back of the frame, and one is for instances where these holes are not available. 

Note: 

The standard frame Clearfield offers already has rear mounting holes.

Frames with rear 

mounting holes

Frames without rear 

mounting holes

If no rear mounting holes are available, the other bracket can be used. You 

will need to hold the bracket up to the frame and drill a pilot hole into the 

frame as shown. Then, you can mount the bracket using the self-tapping 

screw included with the panel. 

The angle of the cable can be adjusted by using different sets of threaded 

holes in the bracket.

Patch Only panels have tails which may need to be routed through the frame and up to the appropriate ladder racks or 

down into the raised floor before securing the cable to the frame.

1.

2.

3.

4.

5.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды