manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 11

11

FieldSmart

®

 FxDS Frame

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 012010 REV H - July 2018

Place the floor panels into position, and tighten the previously installed nuts below the raised panel until they make 

contact with the panel. Put the isolation pad into place (isolation pad may look different than example).

Lift the frame into place. 

Place the square washers onto each rod. Align the edges of the 2” square washer parallel with the slots in the frame 

base to obtain the maximum material overlap. Install the isolation washers (packaged with the isolation pad) onto each 

rod.

Install the remaining hardware (washers, nuts, etc) from the raised floor installation kit.

Note: 

Square 

washers will be 

 

packaged in base

 of frames

Threaded Rod

10.

11.

12.

13.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды