manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 23

23

FieldSmart

®

 FxDS Frame

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 012010 REV H - July 2018

FxDS PON Insert Kit

The FxDS PON Kit allows the user to install (18) 1x32 PON 

splitters onto an FxDS frame system. It is comprised of a 576 

port bulkhead panel that is self contained with specialized fiber 

management for the 1x32 ruggedized splitters. Two FxDS Pon 

inserts can fit on one FxDS Frame.

Note:

 

The PON insert is designed to only be used in a FxDS 

frame system.

There is a FxDS frame system configuration specially designed for 

the PON insert. Because of the PON insert width, the configuration 

does not have interbay management spools.

If you have a standard FxDS Frame you will need to remove the 

interbay spools on the frame that would interfere with the bulkhead 

(see picture).

The bulkhead panel can now be installed using the provided hard

-

ware. The bulkhead is very large and should be installed without 

any cassettes or fiber installed. 

The top 24 ports on both sides are the feeder ports for their re

-

spective sides. Optionally, they can be tie plates with adapters for 

plugging jumpers from active gear into the back.

2.

3.

1.

4.

5.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды