manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 5

5

FieldSmart

®

 FxDS Frame

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 012010 REV H - July 2018

Packaging

The FxDS Frame Kit

 will come in a wood packaging 

crate (88” long x 28” wide x 29” high).

Open the crate by removing the 6 screws and removing 

the lid. The screws are called out by black circles.

Carefully remove the contents. This includes:

One (1) frame and isolation pad, (4) doors, (2) interbays, (2) end guards, a trough kit usually containing (3) troughs, 

a grounding bar and miscellaneous hardware for securing the hinges to the doors and end guards as well as for 

mounting the frame to the floor.

Note:

 

The FxDS Frame system comes in a variety of configurations so the above bill of materials will vary.

This is what the crate will look like while unpacking. Once you confirm all the parts and hardware are available, it is 

time to install the frame.

Note:

 

Floor mounting hardware is NOT included with the standard frame. Hardware is sold as a separate line item

(Clearfield P/N 009106).

1.

2.

3.

4.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды