manualshive.com logo in svg

Clearfield FieldSmart, Руководство по установке

Поделиться
Скачать
Clearfield FieldSmart Скачать руководство пользователя страница 10

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

10

FieldSmart

®

 FxDS Frame

Installation Manual 

 _________________________________________________________

Manual 012010 REV H - July 2018

Install anchors into the floor. Replace raised floor panels and 

insert threaded rods through the four holes.

Note:

 

You are not installing the rods at this point. We are 

measuring the rods to be cut to the appropriate length.

Measure the rods 2.5” above the floor and mark with a 

permanent marker. Remove the rods and cut each rod at the 

mark. Remove the floor panels.

Before installing rods back into the floor, place a nut and then 

a washer on the threaded rods. Take the rod and install it into 

the anchor installed in the floor. 

Tighten the nut down to secure the rod into the floor. Tighten 

each bolt to 65 ft-lbs., +10, -0 ft-lbs. The anchor will expand 

and secure itself to the floor.

Once all four rods are secure, thread another hex nut, then 

washer on each rod. Make sure the nut and washer are 

approximately ½” below the raised floor level. This hardware 

will be tightened down AFTER the frame is set into place but 

BEFORE securely bolting the frame to the floor.

5.

6.

7.

8.

9.

Содержание FieldSmart






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды