background image

CleanStation   Dimension SRS-DT3

TM

Jet action cleaning

4.  Start the cleaning cycle

IMPORTANT:  

Once the system is started, immediately proceed to the next step of adding concentrate; it is 

very important

 to add the

WaterWorks Soluble concentrate 

before

 the 

water gets too warm (86F)

.   Failure to do this may cause the chemical to have an adverse

reaction with the water.

To start the CleanStation

TM

  push          on the controller (see Figure 3).

The CleanStation

TM

 will continue to run until the timer counts down to zero, at which time the system will shut off automatically.

Pressing           will manually stop the cleaning cycle.

IMPORTANT:

  To immediately power off the CleanStation

TM

 (in case of emergency), turn the power switch off and unplug the power

cord.

5.  Temperature setting

The controller is preset to heat and maintain the water temperature at 150F (recommended by Stratasys) 

WARNING

: running the

machine above 150F will void the warranty

.  To change this setting the machine must be running; if it is not running press          to start the

machine.  

WARNING

if the machine isn’t running when changing temperature you may damage the heater.

  Then press and

hold          and use          or          to select the desired temperature.  Parts are most efficiently cleaned with water temperature at or near 150F.

Changing any parameter other than time or heat (do not exceed

 

150 degrees) Viods the warranty.

6.  Timer (run time) setting

The controller is preset to run for four hours.  Most parts take one to two hours to clean, but varying levels of geometric complexity can
increase (or reduce) the time necessary.  To set the run time different from that preset:

(1)  Press and hold the           for 2 seconds.  When             is displayed release the           .

(2)  Press          to display hour             and minutes              .

(3)  Press and hold          while using the          and          keys to adjust the desired run time.

(4)  Press           to exit the menu.

Operation (continued)

Содержание SRS-DT3














Отзывы: