CleanStation SRS-DT3 Скачать руководство пользователя страница 10

Страница: 10 / 13

CleanStation Dimension SRS-DT3

Jet action cleaning

• The CleanStation

requires very little maintenance. Keep it clean by wiping it down with a damp cloth after use. Remember to

always use neoprene safety gloves and eye protection.

• The CleanStation

pump and motor are factory sealed and

do not

require any lubrication or seal replacement.

• When replacing fuses, always unplug power to the CleanStation

and keep the power cord in view. Keeping the power cord in view

will ensure the CleanStation

is not inadvertently plugged back in by someone else.

• Any failure of the product due to negligence or misuse

by the Customer

voids the warranty

. Using the machine for anything other

than its intended purpose or changing anything that results in a failure also

voids the warranty

. Changing any control parameter

other than time and temperature (do not exceed 150 degrees)

voids the warranty

. The Customer is expected to follow the

guidelines for operations stipulated in the Installation, Operation, and Maintenance Instructions.

Maintenance (continued)

(7) Remove material blocking the jets by either pulling the material through the holes, or flushing through the inlet of the

manifold.

(8) Re-install the manifold and tighten the hose clamp.

(9) Re-install the jetplate. Slide the jet plate between the washers and the tank. Be careful not to over-tighten the nuts, for easier

removal in the future.

Содержание SRS-DT3














Результаты поиска

Содержание SRS-DT3

Отзывы:

Похожие инструкции для SRS-DT3

Бренды по названию

Популярные бренды

CleanStation SRS-DT3, Руководство пользователя

Результаты поиска

Содержание SRS-DT3

Отзывы:

Похожие инструкции для SRS-DT3

Бренды по названию

Популярные бренды