CleanStation SRS-DT3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 13

CleanStation SRS-DT3 Скачать руководство пользователя страница 13

CleanStation Dimension SRS-DT3

TM

Jet action cleaning

Warranty Information

PM Technologies warrants that the CleanStation



part cleaning system will be free of defects in materials and workmanship for a period

of one year from the date of shipment. If the product proves defective during the warranty period, PM Technologies, at its option, will:

• repair the product by means of telephone support or send parts at no charge, customer pays for shipping.

Under this product warranty, the Customer must notify PM Technologies or it authorized service representative of the defect before the
expiration of the warranty period. To obtain service under this warranty, the Customer must first contact PM Technologies Telephone
Support personnel or that of its authorized service representative. Telephone Support personnel will work to resolve issues professionally
and quickly, however the Customer must reasonably assist PM Technologies or its authorized representative.

If telephone support is unsuccessful by PM Technologies or its authorized service representative the machine must be shipped back to PM
Technologies and PM Technologies will provide warranty repair (if machine is still under warranty) for parts and labor for products
purchased in the United States and Canada.

If the Customer’s product contains features that enable PM Technologies or its authorized service representative to diagnose and repair
problems with the product remotely, PM Technologies may request that the Customer allow such remote access to the product.
In the maintenance of the product, PM Technologies may use new or equivalent to new parts or assemblies for equal or improved quality.
All defective parts and assemblies become the property of PM Technologies. PM Technologies, at its option, may request the return of
these parts.

Doing any of the following

voids the warranty

: 1) Any failure of the product due to negligence or misuse

by the Customer. 2) Using

the machine for anything other than its intended purpose or changing anything that results in a failure. 3) Changing any control parameter
other than time and temperature (do not exceed 150 degrees). 4) Running the machine with its filter off. 5) Using chemicals that have
not been pre-qualified by PM Technologies. The Customer is expected to follow the guidelines for operations stipulated in the
Installation, Operation, and Maintenance Instructions,

which includes the normal industry safety practice, of plugging the machine

into a 115VAC ground fault interrupt outlet.

«
...
11
12
13

Содержание SRS-DT3














Отзывы:

Нет отзывов