Clarke 2090908 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Clarke 2090908 Скачать руководство пользователя страница 5

5

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

BEFORE USE

POSITIONING THE AIR COMPRESSOR IN THE WORKPLACE

1. ALWAYS carry the compressor using the handle.

2. DO NOT lift by (or put strain on) valves or hoses.

3. Before starting, ensure the compressor is standing on a firm level surface

which does not exceed 10

o

incline, either transversely or longitudinally.

4. Ensure the environment is dry and dust free.

5. Ensure there is adequate ventilation for:

• Air intake to the compressor pump and engine.

• Cooling for the compressor pump and engine.

• Engine exhaust gases.

FILING WITH OIL

The engine and compressor are
supplied without oil inside.

A 1 litre bottle of dual purpose oil is
provided in the box and must be
added before use (approx 0.6 L to
the engine and 0.4 L to the
compressor).

For future use, suitable oils are
available from your CLARKE dealer:

1 litre of SAE30 Engine oil - Part No.
3050852

1 litre of SAE30 Air Compressor oil - Part No. 3050796

AIR COMPRESSOR (PUMP)

Remove the compressor dipstick and
add 0.4 L of compressor oil to the
compressor. Check the oil level on
the dipstick

«
...
3
4
5
6
7
...
»

Содержание 2090908





















Отзывы:

Нет отзывов